製造工程師2013r1測試版的問題，請賈工幫忙！！！

zhang_112

2011有按文件大小分割選項，2013需然沒有此選項，但文件大小是可改的，為啥我改後就是不行？高手們請你們張張嘴謝謝！！！！！

zhang_112

非常感謝！！！！！！！1

zhang_112

賈工你好！我連夜按照你所說的更改但是還是不行，請繼續指教，謝謝！！！！！！！

zhang_112

<BLOCKQUOTE style="MARGIN-RIGHT: 0px" dir=ltr>
<P align=left>#------------------------------------------------------------------------------ # Machine Control File: mcf 1.0 # CAXA CAXPost 1.0 #------------------------------------------------------------------------------ # 後置係統：Fanuc # 描 述：適用於三軸銑床 # 說 明：該文件為後置係統CAXPOST所使用，控製G代碼輸出。以下劃線開頭 # 的字符串請不要改變，否則會導致該文件不可使用。 # # 2005-09-27 Created by CAXA #------------------------------------------------------------------------------ # 機床配置文件的設定 #------------------------------------------------------------------------------ _begin mcfdlg_set abs_code = G90 #絕對編程指令 absinc = 0 #0：絕對編程方式，1：相對編程方式 arc3dmode = 0 #0:不輸出空間圓弧，1:所有圓弧按空間圓弧輸出，2:坐標平麵外的圓弧按空間圓弧輸出 arc_max = 360.000000 #圓弧最大角度 arc_tol = 0.001000 #圓弧離散成直線時精度 arcmode = 0 #0:圓心相對起點，1:起點相對圓心，2:絕對坐標，3:圓心相對終點，4:圓弧半徑為負，當圓心角大於180度時，5:圓弧半徑為正，當圓心角大於180度時，6:圓弧離散成直線 caxis_g00_return_zero = 0 cool_off = M09 #關冷卻液指令 cool_on = M07 #開冷卻液指令 deli_user = #用戶自定義字符，隻有delimode = 3時起作用 delimode = 1 #分隔符模式0：無，1：空格，2：Tab,3：自定義字符 drill_modal = 1 end_char = % #結束符 eob = #行結束符 feed_code = F #速度指令 file_max = 180 #文件最大長度，單位kb file_maxline = 1000 #文件最大行數 firstaxis = 2 firstaxis_stangle = 0.000 fmax_mode = 0 file_limit_on = 1 #0:文件最大長度，1:文件最大行數 g00 = G0 #快速移動指令 g00feed = #快速移動速度 g01 = G1 #直線插補指令 g02 = G2 #順時針圓弧插補指令 g03 = G3 #逆時針圓弧插補指令 g17 = G17 #XY平麵指令 g18 = G18 #ZX平麵指令 g19 = G19 #YZ平麵指令 g3darc = #空間圓弧指令 g40 = G40 #取消刀具補償指令 g41 = G41 #刀具左補償指令 g42 = G42 #刀具右補償指令 g43 = G43 #刀具長度補償指令 inc_code = G91 #相對編程指令 machineaxis = 3 machinetype = 0 prog0_to_caxis_x = 0.000000 prog0_to_caxis_y = 0.000000 prog0_to_caxis_z = 0.000000 prog_no = 1200 #程序號 prog_stop = M30 #程序停止指令 rot1max = 99999.000000 rot1min = -99999.000000 rot2_from_rotc_offset_x = 0.000000 rot2_from_rotc_offset_y = 0.000000 rot2_from_rotc_offset_z = 0.000000 rot2max = 99999.000000 rot2min = -99999.000000 secondaxis = 0 secondaxis_stangle = 0.000000 seq_code = N #行號地址 seq_inc = 5 #行號增量，即每兩個行號之間的間隔 seq_max = 99999 #最大行號 seq_num = 4 #行號位數，隻有seq_zero＝1時才起作用 seq_out = 1 #是否輸出行號1:是，0:否 seq_start = 5 #起始行號 seq_zero = 0 #行號位數是否填滿，1：是，0：否 spn_ccw = M04 #主軸反轉指令 spn_code = S #主軸轉速指令 spn_cw = M03 #主軸正轉指令 spn_stop = M05 #主軸停止指令 start_char = % #起始符 submode = 1 tilt_axis_vx = 0.000000 tilt_axis_vy = 0.000000 tilt_axis_vz = 0.000000 toolcmp_follow = 1 #G41或G42後麵是否加D，等於1時才加，其它就不加。 toolrotlength = 0.000000 _end #------------------------------------------------------------------------------ # 係統變量默認的指令地址符 system variable and register format #------------------------------------------------------------------------------ # 後麵還有若幹 _begin sysvar_register app_h = Z appfeed = F ci = I cj = J ck = K clearance = Z_CLEAR cr = R cx = X cy = Y cz = Z drillfeed = F dwelltime = P_CYCL feed = F holedepth = Z_CYCL holedepth2 = Z_CYCL ntool_adjust_reg = H ntool_cutcom_reg = D ntool_num = T peckdepth = Q_CYCL prog_no = O rotatetable = B safe_h = Z safedis = R_CYCL speed = S startx = X starty = Y startz = Z tool_adjust_reg = H tool_cutcom_reg = D tool_num = T worksurface = Z_WORK _end #------------------------------------------------------------------------------ # 指令地址格式register format #------------------------------------------------------------------------------ #key,name,initvalue,int_num,dec_num,lead,trail,dec,sign,modal,zero,minimum,limit_min,maximum,litmi_max,before,after,formula _begin register_format A,A,0.000000,4,3,0,0,1,0,1,1,-10000.000000,0,10000.000000,0,,,1 B,B,0.000000,4,3,0,0,1,0,1,1,-10000.000000,0,10000.000000,0,,,1 C,C,0.000000,4,3,0,0,1,0,1,1,-10000.000000,0,10000.000000,0,,,1 D,D,0.000000,4,0,0,0,0,0,1,1,-10000.000000,0,10000.000000,0,,,1 DEFAULT,,0.000000,4,6,0,1,1,0,1,1,-10000.000000,0,10000.000000,0,,,1 F,F,0.000000,6,0,0,0,0,0,1,1,0.000000,0,10000.000000,0,,,1 F_CYCL,F,0.000000,4,3,0,0,1,0,1,1,0.000000,0,10000.000000,0,,,1 G,G,0.000000,3,2,1,0,0,0,1,0,0.000000,0,99999.000000,0,,,1 H,H,0.000000,4,0,0,0,0,0,1,1,0.000000,0,10000.000000,0,,,1 I,I,0.000000,4,3,0,0,1,0,0,1,-10000.000000,0,10000.000000,0,,,1 J,J,0.000000,4,3,0,0,1,0,0,1,-10000.000000,0,10000.000000,0,,,1 K,K,0.000000,4,3,0,0,1,0,0,1,-10000.000000,0,10000.000000,0,,,1 M,M,0.000000,4,0,0,0,0,0,1,1,0.000000,0,10000.000000,0,,,1 N,N,10.000000,4,0,0,0,0,0,0,0,0.000000,0,99999.000000,1,,,1 O,O,1000.000000,4,0,0,0,0,0,0,0,0.000000,0,9999.000000,0,,,1 P,P,0.000000,4,0,0,0,0,0,1,1,-10000.000000,0,10000.000000,0,,,1 P_CYCL,P,0.000000,4,3,0,0,1,0,1,1,-10000.000000,0,10000.000000,0,,,1 Q_CYCL,Q,0.000000,4,3,0,0,1,0,1,1,-10000.000000,0,10000.000000,0,,,1 R,R,0.000000,4,3,0,0,1,0,0,1,-10000.000000,0,10000.000000,0,,,1 R_CYCL,R,0.000000,4,3,0,0,1,0,1,1,-10000.000000,0,10000.000000,0,,,1 S,S,0.000000,6,0,0,0,0,0,1,1,0.000000,0,10000.000000,0,,,1 T,T,0.000000,2,0,0,0,0,0,1,1,0.000000,0,10000.000000,0,,,1 TT,,0.000000,2,0,0,0,0,0,1,1,0.000000,0,10000.000000,0,,,1 U,U,0.000000,4,3,0,0,1,0,1,1,-10000.000000,0,10000.000000,0,,,1 V,V,0.000000,4,3,0,0,1,0,1,1,-10000.000000,0,10000.000000,0,,,1 W,W,0.000000,4,3,0,0,1,0,1,1,-10000.000000,0,10000.000000,0,,,1 X,X,0.000000,4,3,0,0,1,0,1,1,-10000.000000,0,10000.000000,0,,,1 Y,Y,0.000000,4,3,0,0,1,0,1,1,-10000.000000,0,10000.000000,0,,,1 Z,Z,0.000000,4,3,0,0,1,0,1,1,-10000.000000,0,10000.000000,0,,,1 Z_CLEAR,Z,0.000000,4,3,0,0,1,0,1,1,-10000.000000,0,10000.000000,0,,,1 Z_CYCL,Z,0.000000,4,3,0,0,1,0,1,1,-10000.000000,0,10000.000000,0,,,1 Z_WORK,Z,0.000000,4,3,0,0,1,0,1,1,-10000.000000,0,10000.000000,0,,,1 _end #------------------------------------------------------------------------------ # 程序輸出控製 #------------------------------------------------------------------------------ _begin program # 輸出空間圓弧 arc_3d { $seq,$sgplane,$sgcode,$sgabsinc, $cx,$cy,$cz,XI($ci),YJ($cj),ZK($ck),$feed,$eob,@ } # 圓弧輸出格式# 圓弧輸出圓心方式 arc_center { $seq,$sgabsinc,$sgplane,$sgcode, $cx,$cy,$cz,$ci,$cj,$ck,$feed,$eob,@ } # 圓弧輸出半徑方式 arc_radius { $seq,$sgabsinc,$sgplane,$sgcode, $cx,$cy,$cz,$cr,$feed,$eob,@ } # 高速深孔加工循環 cycle_g73 { $seq,"G99 G73 ",$cx,$cy,$holedepth2,$safedis,$peckdepth, $drillfeed,$eob,@ } # 反攻絲循環 cycle_g74 { $seq,"G99 G74 ",$cx,$cy,$holedepth2,$safedis,$dwelltime, $drillfeed,$eob,@ } # 精鏜循環 cycle_g76 { $seq,"G99 G76 ",$cx,$cy,$holedepth2,$safedis,$peckdepth, $dwelltime,$drillfeed,$eob,@ } # 取消固定循環指令 cycle_g80 { $seq,"G80",$eob,@ $seq,$sgabsinc,$sgcode,$startz,$eob,@ $seq,$sgabsinc,$sgcode,$startx,$starty,$eob,@ $seq,$cool_off,$eob,@ $seq,$spn_stop,$eob,@ } # 鑽孔循環（中心鑽） cycle_g81 { $seq,"G99 G81 ",$cx,$cy,$holedepth2,$safedis,$drillfeed,$eob,@ } # 帶停頓的鑽孔循環 cycle_g82 { $seq,"G99 G82 ",$cx,$cy,$holedepth2,$safedis, $dwelltime,$drillfeed,$eob,@ } # 深孔加工循環 cycle_g83 { $seq,"G99 G83 ",$cx,$cy,$holedepth2,$safedis,$peckdepth, $drillfeed,$eob,@ } # 攻絲循環 cycle_g84 { $seq,"G99 G84 ",$cx,$cy,$holedepth2,$safedis,$dwelltime, $drillfeed,$eob,@ } # 鏜孔循環 cycle_g85 { $seq,"G99 G85 ",$cx,$cy,$holedepth2,$safedis,$drillfeed,$eob,@ } # 鏜孔循環(孔底主軸停止) cycle_g86 { $seq,"G99 G86 ",$cx,$cy,$holedepth2,$safedis,$drillfeed,$eob,@ } # 反鏜循環 cycle_g87 { $seq,"G99 G87 ",$cx,$cy,$holedepth2,$safedis,$peckdepth, $drillfeed,$eob,@ } # 鏜孔循環(暫停後主軸停止) cycle_g88 { $seq,"G99 G88",$cx,$cy,$holedepth2,$safedis, $dwelltime,$drillfeed,$eob,@ } # 鏜孔循環(孔底有暫停) cycle_g89 { $seq,"G99 G89",$cx,$cy,$holedepth2,$safedis, $dwelltime,$drillfeed,$eob,@ } cycle_last_run { $seq,"G98 ",$cx,$cy,$eob,@ } # 鑽孔循環執行，特別是在鑽同樣的孔且用同一把刀具時可以被多次調用 cycle_run { $seq,$cx,$cy,$eob,@

zhang_112

顯得有點雜亂，不知賈工能看清不，我分別在在文字說明前麵和後麵都加了試，都不行。麻煩你了，謝謝！！！！

jxc

它需要單獨一行的。
我試了是可以起作用的。
更改完後應該是這樣的：

fmax_mode        = 0        #0:文件最大長度，1:文件最大行數
file_limit_on = 1
g00        = G0        #快速移動指令

zhang_112

謝謝賈工！已搞定